Header Parameters

 
Name: Description: Used in/Using parameters: Default expression (mm):
HHeader - Used In:
HGirder
(Girder)
PHx, PHy, FH
(Header) 		60
L Defines the real length of the box, depending on the dimension type ( DT ). However, the actual length of the base in the drawing is calculated by taking into account not only L, but also DT and FD,and is measured through the Lss and Lss1 parameters.

L is only used in the expressions of the actual score-to-score length parameters Lss and Lss1. This means that changing the expression of L will change the length (Lss and Lss1) of the current resizable design, too.

Used In:
TL, TO
(Lock Hole)
Using:
ShLss
(Shelf)
PWGirder
(Girder)
LHW1
(Lock Hole) 		ShLss+2*O90y(d(Shelf), fd(Shelf))+2*(PWGirder+2*O90y(d(Girder), fd(Girder)))+2*LHW1
PHx Header: - Using:
HHeader
(Header) 		HHeader-PHCorrX(d(), fd())
Shelf: - Using:
HTray
(Shelf) 		HTray-PHCorrX(d(), fd())
PHy Header: - Using:
HHeader
(Header) 		HHeader-PHCorrY(d(), fd())
Shelf: - Using:
HTray
(Shelf) 		HTray-PHCorrY(d(), fd())-O90x(d(Shelf), fd(Shelf))
DC Defines the Header distance. Used In:
DxDCT, DxDCT1
(Header) 		DC1x(d(Header), fd(Header))
DxDCT Header: Defines the horizontal size of the Header taper. Using:
DC
(Header) 		DC
Shelf: Defines the horizontal size of the Shelf taper. Using:
DCShelf
(Shelf) 		DCShelf
DxDCT1 Header: - Used In:
LHO1
(Lock Hole)
Using:
DC
(Header) 		DC
Shelf: - Used In:
LHO1
(Lock Hole)
Using:
DCShelf
(Shelf) 		DCShelf
UL Defines whether to use layers (relative to the number and the type of the flaps). If you imagine, that in the current design, each two opposite side flaps form a layer, then the other two opposite ones form another layer that overlaps the first one. Therefore, if the number of the layers is n, you have to apply 'n-1' corrections to the sides adjoining the respective flaps (layers). Of course, the Layers Parameters take into account all these corrections.

UL is a selection type parameter - it uses Boolean selection type , predefined in the Corrugated parameter template. The 2 predefined entries are as follows:

  • Yes - use this type when you wish to use layers, ie. whwn there are overlapping layers (flaps, tucks and etc.)the system to take it into account when calculating the design ( in this case L=Lss ).

  • No - use it when you do not have to use layers or the corrections may be neglected.

To change the expression of UL, click in the Expression column field of UL in the Parameters tabular pane tab and select the desired option from the list.

Used In:
LHO1
(Lock Hole)
FH
(Header) 		Yes
LSC Defines the layer step crease. Used In:
LHO1
(Lock Hole)
FH
(Header) 		LSCf(d())
FH Header: Defines the flap height. Using:
HHeader, UL, LSC
(Header) 		HHeader+UL*LSC
Shelf: Defines the flap height. Using:
HLShelf, ShWss, HTray
(Shelf)
UL, LSC
(Header) 		HTray+UL*LSC
DXT - - DxT(d())
DxT1 - Used In:
DyT1
(Header) 		d()
DyT1 - Using:
DxT1
(Header) 		DxT1