| Parameter: | Group: | Used in/Using parameters (direct dependence): | Where would the design resize when I change the parameter expression: |
| A | Main |
Used In: B (Main) LTO, SO (Locking Flap) PH1 (Flaps) |
Length of the box |
| B | Main |
Used In: LFTL, LTO1, SO1 (Locking Flap) PH, PH1, PH2 (Flaps) Using: A (Main) |
Width of the box |
| H | Main | - | Height |
| GLC | Main | - | Correction because of the glue flap |
| UL | Main |
Used In: PH2 (Flaps) |
Defines if layers should be used |
| LSC | Layers |
Used In: PH2 (Flaps) |
Layer step crease |
| LTO (A10.30.03.03) | Locking Flap |
Used In: LFH (Locking Flap) Using: A (Main) |
Locking tongue offset |
| FR (A10.30.03.03) | Locking Flap |
Used In: LFH (Locking Flap) |
Fillet Radius |
| LFH (A10.30.03.03) | Locking Flap |
Using: LTO, FR (Locking Flap) |
Locking Flap Height |
| LFA | Locking Flap | - | Locking flap angle |
| LFTW (A10.30.03.03.a) | Locking Flap |
Used In: LFTL (Locking Flap) |
Locking flap tongue width |
| LFTL (A10.30.03.03.a) | Locking Flap |
Using: B (Main) LFTW, SO1 (Locking Flap) |
Locking flap tongue length |
| LTO1 (A10.30.03.03) | Locking Flap |
Using: B (Main) |
Locking tongue offset |
| Z (A10.30.03.03) | Locking Flap |
Used In: SLL (Tuck End) |
Length of lock on dust flap |
| ZZ (A10.30.03.03) | Locking Flap | - | Horizontal size of dust flap bevel |
| beta (A10.30.03.03) | Locking Flap | - | - |
| LFBA (A10.30.03.03) | Locking Flap | - | - |
| EdgeType | Locking Flap |
Used In: FC1, LFC2 (Locking Flap) |
- |
| FC (A10.30.03.03) | Locking Flap | - | Flap correction |
| FC1 (A10.30.03.03) | Locking Flap |
Used In: DxCh (Locking Flap) Using: EdgeType (Locking Flap) |
Flap correction |
| DxCh | Locking Flap |
Using: FC1, LFC2 (Locking Flap) |
- |
| SO (A10.30.03.03.a) | Locking Flap |
Used In: BO (Locking Flap) Using: A (Main) |
Slit Offset |
| SO1 (A10.30.03.03.a) | Locking Flap |
Used In: LFTL, SO2 (Locking Flap) Using: B (Main) |
Slit Offset |
| SO2 (A10.30.03.03.a) | Locking Flap |
Using: SO1, LFC1 (Locking Flap) |
Slit Offset |
| BO (A10.30.03.03.a) | Locking Flap |
Using: SO (Locking Flap) |
Length of lock on dust flap |
| ExtL | Locking Flap | - | - |
| ChL | Locking Flap | - | - |
| LFC1 (A10.30.03.03.a) | Locking Flap |
Used In: SO2 (Locking Flap) |
Locking flap correction |
| LFC2 (A10.30.03.03.a) | Locking Flap |
Used In: DxCh (Locking Flap) Using: EdgeType (Locking Flap) |
Locking flap correction |
| TEH | Tuck End |
Used In: TER (Tuck End) |
Tuck end height |
| TER (A10.30.03.03.a) | Tuck End |
Using: TEH (Tuck End) |
Tuck end radius |
| TEC | Tuck End |
Used In: SLL (Tuck End) |
Tuck end correction |
| SLO (A10.30.03.03) | Tuck End | - | Slit lock offset |
| SLD (A10.30.03.03) | Tuck End | - | Slit lock depth |
| SLL (A10.30.03.03) | Tuck End |
Using: Z (Locking Flap) TEC (Tuck End) |
Slit lock length |
| PH | Flaps |
Using: B (Main) |
Panel Height |
| PH1 | Flaps |
Used In: PH2 (Flaps) Using: A, B (Main) |
Panel height |
| CR1 (A10.30.03.03.a) | Panel | - | Cut Radius |
| PH2 | Flaps |
Using: B, UL (Main) LSC (Layers) PH1 (Flaps) |
Panel height |
| DxT1 (A10.30.03.03) | Flaps | - | Horizontal size of the taper |
| DyT1 (A10.30.03.03) | Flaps | - | Vertical size of the taper |
| GL | Glue Flap | - | Glue flap width |
| GLA | Glue Flap |
Used In: GLA1 (Glue Flap) |
Webbed flap angle |
| GLA1 (A10.30.03.03.a) | Glue Flap |
Using: GLA (Glue Flap) |
Glue flap angle |