| Parameter: | Group: | Used in/Using parameters (direct dependence): | Where would the design resize when I change the parameter expression: |
| A | Main |
Used In: alpha (Main) |
Length of the box |
| B (D10.21.04.00.b) | Main | - | Width of the box |
| B1 (D10.21.04.00, D10.21.04.00.a) | Main |
Used In: B2, alpha (Main) TL, TO (Lock Hole) |
- |
| B2 (D10.21.04.00, D10.21.04.00.a) | Main |
Used In: alpha (Main) TL4, TO4 (Lock Hole) Using: B1 (Main) |
- |
| H | Main |
Used In: PH (Panel) CO (Webbed Flaps) FR (Webbed Flap) TPH (Trapezium) |
Height |
| BAng (D10.21.04.00.b) | Main |
Used In: WFA1 (Webbed Flaps) BAng1 (Trapezium) |
Bevel angle |
| WFA1 (D10.21.04.00.b) | Webbed Flaps |
Using: BAng (Main) |
Webbed flap angle 2 |
| alpha (D10.21.04.00, D10.21.04.00.a) | Main |
Using: A, B1, B2 (Main) |
Triangular flap angle |
| UL (D10.21.04.00.a) | Main | - | Defines if layers should be used |
| LSC (D10.21.04.00.a) | Layers | - | Layer step crease |
| PH (D10.21.04.00, D10.21.04.00.a) | Panel |
Using: H (Main) |
Panel Height |
| PC1 (D10.21.04.00.a) | Panel |
Used In: TO1 (Lock Hole) |
Panel correction |
| DxTB1 (D10.21.04.00, D10.21.04.00.a) | Panel | - | Horizontal size of trapezium bevel |
| TL (D10.21.04.00.a) | Lock Hole |
Used In: TL1, TO1, TO2 (Lock Hole) Using: B1 (Main) |
Tongue length |
| TH (D10.21.04.00.a) | Lock Hole |
Used In: TH1 (Lock Hole) |
Tongue height |
| DxTT (D10.21.04.00.a) | Lock Hole |
Used In: DxTT1 (Lock Hole) |
Horizontal size of the tongue taper |
| TO (D10.21.04.00.a) | Lock Hole |
Used In: TO1, TO2 (Lock Hole) Using: B1 (Main) |
Tongue offset |
| TL1 (D10.21.04.00.a) | Lock Hole |
Used In: TO1, TO2 (Lock Hole) Using: TL (Lock Hole) |
Tongue length |
| TH1 (D10.21.04.00.a) | Lock Hole |
Using: TH (Lock Hole) |
Tongue height |
| DxTT1 (D10.21.04.00.a) | Lock Hole |
Using: DxTT (Lock Hole) |
Horizontal size of the tongue taper |
| TO1 (D10.21.04.00.a) | Lock Hole |
Using: PC1 (Panel) TL, TO, TL1 (Lock Hole) |
Tongue offset |
| TO2 (D10.21.04.00.a) | Lock Hole |
Using: TL, TO, TL1 (Lock Hole) |
Tongue offset |
| TL4 (D10.21.04.00.a) | Lock Hole |
Used In: TL5, TO5 (Lock Hole) Using: B2 (Main) |
- |
| TO4 (D10.21.04.00.a) | Lock Hole |
Used In: TO5 (Lock Hole) Using: B2 (Main) |
- |
| TL5 (D10.21.04.00.a) | Lock Hole |
Used In: TO5 (Lock Hole) Using: TL4 (Lock Hole) |
- |
| TO5 (D10.21.04.00.a) | Lock Hole |
Using: TL4, TO4, TL5 (Lock Hole) |
- |
| DxTB2 (D10.21.04.00) | Panel | - | Horizontal size of trapezium bevel |
| WFC (D10.21.04.00) | Webbed Flap |
Used In: FR (Webbed Flap) |
Webbed flap correction |
| WFA2 | Webbed Flap | - | Webbed flap angle 2 |
| CO (D10.21.04.00.b) | Webbed Flaps |
Used In: FR (Webbed Flap) Using: H (Main) |
Cut offset |
| FR | Webbed Flap |
Using: H (Main) WFC (Webbed Flap) CO (Webbed Flaps) |
Fillet Radius |
| TPH (D10.21.04.00.b) | Trapezium |
Using: H (Main) |
Trapezium height |
| BAng1 (D10.21.04.00.b) | Trapezium |
Using: BAng (Main) |
Trapezium bevel angle |