| Parameter: | Group: | Used in/Using parameters (direct dependence): | Where would the design resize when I change the parameter expression: |
| DIC | Main |
Used In: L1 (Main) PH, DxPT, DyPT, DxPB (Hexagonal Panel) |
- |
| L1 | Main |
Used In: HL, HO1, HO2 (Hole) FH (Crash Lock) Using: DIC (Main) |
Length |
| H | Main |
Used In: HW, VHO (Hole) |
Height |
| UL | Main |
Used In: TPH (Trapezium) |
Defines if layers should be used |
| LSC | Layers |
Used In: TPH (Trapezium) |
Layer step crease |
| GLC | Main | - | Correction because of the glue flap |
| CrO | Main |
Used In: VHO (Hole) |
Crease offset |
| TEO | Hexagonal Panel |
Used In: PH (Hexagonal Panel) |
Tuck End Offset |
| TCR | Tumb Cut | - | Tumb Cut radius |
| HL | Hole |
Used In: HO1, HO2 (Hole) Using: L1 (Main) |
Hole Length |
| HW | Hole |
Used In: HFR, VHO (Hole) Using: H (Main) |
Hole Width |
| HFR | Hole |
Using: HW (Hole) |
Hole fillet radius |
| VHO | Hole |
Using: H, CrO (Main) HW (Hole) |
Vertical hole offset |
| HO1 | Hole |
Using: L1 (Main) HL (Hole) |
Hole offset |
| HO2 | Hole |
Using: L1 (Main) HL (Hole) |
Hole offset |
| FH | Crash Lock |
Used In: CLPH1, CLPH4 (Crash Lock) Using: L1 (Main) |
Flap height |
| CLPA | Crash Lock | - | Bevel angle of the crash lock panel |
| FA1 | Crash Lock | - | - |
| TW1 | Crash Lock | - | - |
| CLFA | Crash Lock |
Used In: CT1, CLPH3 (Crash Lock) GLA (Glue Flap) |
Crash lock flap angle |
| CLFA1 | Crash Lock | - | - |
| CLPH1 | Crash Lock |
Using: FH (Crash Lock) |
Crash lock panel height |
| CLFA2 | Crash Lock |
Used In: c, CT1, CLPH3 (Crash Lock) |
- |
| CLPH2 | Crash Lock |
Used In: c, CLPH4 (Crash Lock) |
- |
| c | Crash Lock |
Used In: CT1, CLPH3 (Crash Lock) Using: CLFA2, CLPH2 (Crash Lock) |
- |
| CT1 | Crash Lock |
Used In: FW (Crash Lock) Using: CLFA, CLFA2, c (Crash Lock) |
Correction of the trapezium |
| CLPH3 | Crash Lock |
Using: CLFA, CLFA2, c (Crash Lock) |
- |
| CLPH4 | Crash Lock |
Used In: TW (Crash Lock) Using: FH, CLPH2 (Crash Lock) |
- |
| TW | Crash Lock |
Using: CLPH4 (Crash Lock) |
Tongue width |
| FW | Crash Lock |
Using: CT1 (Crash Lock) |
Frame width |
| GL | Glue Flap | - | Glue flap width |
| GLA | Glue Flap |
Using: CLFA (Crash Lock) |
Webbed flap angle |
| PH | Hexagonal Panel |
Used In: DyPT (Hexagonal Panel) Using: DIC (Main) TEO (Hexagonal Panel) |
Panel Height |
| DxPT | Hexagonal Panel |
Used In: BAng1 (Trapezium) Using: DIC (Main) |
Horizontal size of the panel taper |
| DyPT | Hexagonal Panel |
Used In: BAng1, TPH (Trapezium) Using: DIC (Main) PH (Hexagonal Panel) |
Vertical size of the panel taper |
| DxPB | Hexagonal Panel |
Using: DIC (Main) |
Horizontal size of the panel bevel |
| BAng1 | Trapezium |
Using: DxPT, DyPT (Hexagonal Panel) |
Trapezium bevel angle |
| BAng2 | Trapezium | - | Trapezium bevel angle |
| TPH | Trapezium |
Using: UL (Main) LSC (Layers) DyPT (Hexagonal Panel) |
Trapezium height |
| GLA1 | Glue Flap | - | Glue flap angle |